KVM: SVM: Trigger new ASID allocation in both VMCBs on pCPU switch
Default status is the baseline for the product, each version can override it (e.g. patched versions marked unaffected).
| Vendor | Product | Default status | Versions | ||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Linux | Linux | unaffected |
|
||||||||||||||||||||||||
| Linux | Linux | affected |
|
No data.
No data.
No data available yet.
No CVSS v4.0
No CVSS v3.1
No CVSS v3.0
No CVSS v2
This CVE is not in the KEV list.
No EPSS score available.
Key SSVC decision points have not yet been added.
| Type | Values Removed | Values Added |
|---|---|---|
| Description | In the Linux kernel, the following vulnerability has been resolved: KVM: SVM: Trigger new ASID allocation in both VMCBs on pCPU switch When the pCPU where the VMCB was most recently used is switched, reset the ASID generation in both VMCBs, triggering new ASID allocation for the immediate VMRUN as well as the next VMRUN on the other VMCB. The ASID is shared between vmcb01 and vmcb02, and gets flushed on every nested transition. However, since pCPU tracking is done per VMCB, it is possible for one VMCB to allocate a new ASID when migrated to a new pCPU, and then the other VMCB reuses that ASID on the old pCPU. This can result in the same ASID being used by multiple vCPUs on the old pCPU. Example scenario: - vCPU runs on pCPU A, vmcb01 is active, asid=1. - vCPU migrates to pCPU B, vmcb01 pCPU changes, new asid=2. - Another vCPU runs on pCPU A and allocates asid=2 as well. - vCPU migrates back to pCPU A, and then switches to vmcb02 before it runs again with vmcb01. - No pCPU switch is detected for vmcb02, so VMRUN is done with asid=2. - Two vCPUs end up using asid=2 on the same pCPU. Keep the VMCB dirtying to the active VMCB only. Clean bits are tracked by a pCPU for each VMCB, so do not unnecessarily dirty a VMCB if its pCPU does not change. Additionally, initialize the tracked pCPU for vmcb02 to -1 on nested enablement as hardening, so that a new ASID allocation is always triggered when nested is disabled and re-enabled. No performance regression was noticed when overcommitting L1 vCPUs in L0 (to force rescheduling), pinning L1 <-> L2 vCPUs, and running CPUID in a tight loop bouncing between 2 vCPUs in L2. An alternative (and perhaps more proper) fix would be tracking the ASID per-VMCB instead (e.g. [1]). However, that's a more involved change, and it would result in having different ASIDs for L1 and L2 without actually properly maintaining them. It would probably work because all TLB flushes target the current VMCB, and the other VMCB is always flushed on nested transitions, but the code ends up in an arguably more fragile state. Punt a proper clean fix to an incoming (and overdue) overhaul of SVM's ASID usage [2]. [1] https://lore.kernel.org/lkml/20250205182402.2147495-2-yosry.ahmed@linux.dev [2] https://lore.kernel.org/kvm/20260728003557.1136583-1-yosry@kernel.org | |
| Title | KVM: SVM: Trigger new ASID allocation in both VMCBs on pCPU switch | |
| First Time appeared |
Linux
Linux linux Kernel |
|
| CPEs | cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:* | |
| Vendors & Products |
Linux
Linux linux Kernel |
|
| References |
|
No weakness.
No data.
No data.
No data.
No data.